Product DescriptionThe XZG series Spin Flash Dryer is the new type dryer machine with patent; it was designed base on foreign advance technology, combined with the actual situation of domestic drying by ourselves.
The hot air be put into the flash dryer tower from the bottom of dryer body air inlet, it will be with the high speed air flow all rise in the dryer tower ,at the same time we can adjust the annular space
Depend on the different kind of materials, let the air speed goes in the best suitable state.
The material with High speed rotary motion under the impact of airflow and drive dispersed quickly. However the big size granulate and wet particular clusters cannot crush with high speed rotary motion, so it will fall into the crushing plant under the effect of gravity forcibly broken and particulates. and then with the high speed air flow going up and finish the drying process.
The rotor at the conical base of the drying chamber fluidizes product particles in a drying-efficient hot air flow pattern in which any wet lumps are rapidly disintegrated. Using the heat from the airstream, the material dries as it is conveyed. Product is separated using cyclones, and/or bag filters. Typically, cyclones are followed by scrubbers or bag filters for final cleaning of the exhaust gases to meet current emission requirements.
Airborne, fine particles pass through a classifier at the top of the drying chamber, while larger particles remain in the air flow for further drying and powdering
1. Adopt 2 lines tangential air enter into volute at the best position,it will improve or remove blind Angle of wind and also the wind in the weak
2.Be good at control the powder's moisture,fineness,and hold time.for control the speed coordinating and unifying at spinning disk work with wind-enter ,it can ensure the outlet wind with low temperature,it will also reduce the energy consumption.
3. The special alloy steel be used in the rotary blade,the layout structure with unique,it have the character of small erosion,contact surface wide,cutting force strong.
4. Adopt the newly leak-proof structure,the main engine bearing life will be delay,and the bearing black with the cooling device.
5. In order to ensure the powder water content less than 0.5%,so increase the height than the original basis ,it also equip with spinning disk,it will make the powder quality and particle size meet with your requirement.
Due to the gas-solid corresponding relative velocity big,even though the mix temperature around 80~90℃,the powder temperature still on below 45℃ condition,it will help to packing and save energy.
| Diameter of chamber (mm)
| Air amount (m³/h)
||350-500||1150-2000||2450- 4500||4450- 7550||7000- 12500||10000- 20000||18000-36000||28200- 56500|
| Evaporate capacity
| Max power
| Max height (mm)
| Occupied area (m²)
1.To effectively control final moisture content and fineness by spinning disk and the inlet wind speed.
2. The Spinning blade use the special alloy steel, which With less wear, wide contact surface, big cutting force etc
3.it is good at in deal with heat-sensitive materials, there are Cooling water protection device in the high temperature area, it avoid the material go to Coking discoloration in success.
4. Small system resistance, high thermal efficiency, good operating environment, the intensity of labor is low
5.The body tower uses new type seal structure, Extend bearing life cycle, and the Bearing casing also with a water circulating cooling device.Application
This is flash dryer was exported to the Korea,which evaporate amount reach to 32.5T/h,the electric+Oil to be as the heat source.the most famous be fitting in drying filter cake form material.
This is flash dryer was exported to the Canada,which evaporate amount reach to 10kg/h,the electric to be as the heat source.the most famous be fitting in drying filter cake form material.
This pilot flash dryer are popular used in pilot plant ,the customer feed the filter cake material into it for testing ,
to know much more about the
materal's character.the evaporate amount only 5kg/h,the electric to be as heating source .
1. Chemical Industry:
white carbon,amino acid,catalyst,dyestuff intermediate,sodium fluoride,compund fertilizer,etc.
2. Plastics and resin:
AB,ABS emulsion, uric acid resin,phenolic aldehyde resin,urea-formaldehyde resin,polythene,etc.
3. Food Industry:
oats,chicken juice,coffee,instant dissoluble tea,protein,soybean,peanut protein,hydrolysate,etc.
corn syrup,corn starch,glucose,pectin,malt sugar,sorbic acid potassium,etc.
aluminium oxide,ceramic tile material,magnesium oxide,talcum,etc.
1. Design and production
We solicit buyers opinions widely at the design and production stage of equipment; especially at the stage of plan and elevation arrangement, we give full consideration to buyers' site conditions and public engineering conditions, and pay concurrent attention to the optimum combination when assuring the quality of equipment.
2. Installation and commissioning
After the equipment is delivered to buyers factory, we will dispatch full-time technical personnel to instruct buyers' installation and to take charge of commissioning until normal use of the equipment.
Before buyers use our equipment normally, our commissioning personnel will organize buyers' relevant personnel to accept training, which covers the maintenance and care of equipment, timely repair of common faults, and procedures for operation of equipment.
We provide one-year warranty for our equipment. For damage of equipment arising from non-artificial factors within the warranty period, we will provide repair service for free; and for damage of equipment arising from artificial factors, we will provide repair service in time and collect corresponding cost.
5. Maintenance and period
For damage of equipment after expiration of warranty period, we will provide on-site repair service within 24h/48h for enterprises inside/outside the province after receiving buyers' notification. The service provided after expiration of warranty period is fee-based, and flat cost will be collected each time when the service is provided.
This is spray dryer are customized by Slovenia, the evaporate amount reach to 2500 kg/h,the electric+oil to be as heat source,it is used widly in chemical filed.
YPG-1800 ,exported to the Malaysia.
XZG-3,exported to the Korea.
DW5-2x9 ,exported to the Kazakhstan
Jinan Joysun Machinery Co., Ltd., relying on strong technical support, advanced production equipment, excellent processing technology and scientific detection methods, we ensure product quality and delivery time, and provide a fully optimized technical solution according to your requirements. Jinan Joysun Machinery Co., Ltd. for thawing of meat products and seafood, the equipment has stable performance, reliable quality and short thawing time. It is an ideal defrosting equipment for high-tech meat products, made of stainless steel, conforming to food production standard. Welcome new and old customers to inquire. Our international business covers customers all over the world. We have competitive prices and are proud of our excellent after-sales service. The working attitude of the company and the continuous improvement of the innovation concept will lead Tuo Bo and you to step into the brilliant future hand in hand and create a better future.
Through continuous exploration and practice, the company has developed the advantages of low investment, high efficiency, low operation cost, high product quality and convenient control and operation. The microwave frequency thawing equipment with microwave frequency of 915MHz and output power of 20kw-200kw is above. For food processing enterprises such as chain fast food industry in China, food thawing is provided, and the improvement of food thawing technology in China is also renewed. The benefit is not only "farsightedness", but also at the foot of the eyes. According to experts, the traditional food thawing are based on heat conduction method, material surface temperature is higher than the internal temperature in the thawing process, inevitably there will be drop loss, which will increase the business loss. If merchants use microwave dryer, black microwave iron oxide XSG Series Flash Dryer in pigment industry power, material temperature and transmission speed can be used to achieve adjustable linkage, and the overall heating process control advantages can greatly reduce material consumption and improve food utilization. In addition, as the microwave thawing only needs electricity, no need to consume a lot of water, in the low carbon era, this is not lost a recommended fashion trend.
microwave dryer is a new type of environmental protection drying method. When dry, black microwave iron oxide XSG Series Flash Dryer in pigment industry directly to the medium molecules converted into heat, because the black microwave iron oxide XSG Series Flash Dryer in pigment industry penetrating performance of heating medium and at the same time, no need to heat conduction, so the heating speed is very fast, the water content below 30% of the food, the drying speed can be shortened hundreds of times.
microwave dryer advantages of equipment
1, microwave dryer, short, fast
Conventional thermal sterilization is used to transmit heat from the surface of the food to the interior through heat conduction, convection, or radiation. It often takes a long time to get the germicidal temperature. The black microwave iron oxide XSG Series Flash Dryer in pigment industry is the direct interaction between microwave energy and microorganisms such as food and bacteria. The interaction between heat effect and non thermal effect can achieve fast warming and bactericidal action, and the processing time is greatly reduced. The sterilization effect of various materials is usually 3-5 minutes.
2, black microwave iron oxide XSG Series Flash Dryer in pigment industry low temperature sterilization keep the nutrition and traditional flavor The black microwave iron oxide XSG Series Flash Dryer in pigment industry is through special heat and non thermal effect sterilization, compared with conventional thermal sterilization, it can get the desired disinfection effect at relatively low temperature and short time. Practice shows that the general sterilization temperature can reach the effect at 75-80 degrees centigrade. In addition, microwave dryer processed foods can retain more nutrients and color, aroma, taste, shape and other flavors, and have puffing effect. For example, the vitamin C retained in vegetables treated by conventional heat treatment is 46-50%, while that in microwave treatment is 60-90%, while that in conventional heating is 58%, while that in microwave heating is 84%.
3 microwave dryer and black microwave iron oxide XSG Series Flash Dryer in pigment industry save energy Conventional thermal sterilization often has heat loss in the environment and equipment, and microwave is directly treated to food, so there is no extra heat loss. In addition, the conversion efficiency of the electric energy to the microwave energy is in the 70-80%, and the power is generally reduced to 30-50%.
Copyright © 2017 - 2019Shandong Leader Machinery All Rights Reserved